Let the chaos commence! It’s installation week and hopefully not chaos! We received a text from our lead installer on the Sat prior to Monday start date. We also had a phone call but we hate phones, so a text followed. He introduced himself and advised an ETA.
Day One Octopus Energy Heat Pump Install
Monday morning! He was on time, can you detect that I’m quite keen on being on time?! Followed shortly after by approximately 7 million colleagues, ok, it was 6 I think, possibly more, I lost track.
Another guided tour followed so he could orientate himself, though he had seen the numerous photos/videos from the survey.
After this he set one of the installers covering the whole house carpets with carpet protectors/ shrink wrap. At least anywhere they were needing to walk. We had cunningly picked one of the wettest, windiest and muddiest weeks going for this.
By 9.30am the system had been drained and every radiator that wasn’t staying had been evicted from the house! Old cylinder and heating gubbins were also removed. We were quite chilled out about the lack of hot water for a couple of days or so. There was an offer of electric heaters, blankets, and fans to take the chill off the house. But I declined as we have been heating the house with electric panel heaters anyway. But good to hear that was offered.
So far, very efficient! Had a few conversations along the way about how they are going to do things. Sensible conversations though, I didn’t feel shoe horned into anything. I feel that’s really important, there’s nothing worse than a big project like this where you regret something that you were pressured into choosing.
Had a couple of chats with their electrician and the 2nd electrician – new to Octopus but experienced – about various aspects of the installation. Mainly locations of bits, the new consumer unit location, cable routes. To be honest, he was quite sensible and concerned about aesthetics as much as ourselves. Thermostat location to avoid the need for awful surface mount trunking for example, no one likes that!
End of the First Day
By the end of the first day I had my daily walk through from the lead installer to advise on progress and check I was ok with how it was proceeding. We had all the new radiators attached to walls and carpets/floorboards back down where they had been lifted. The two main bedroom radiators had been plumbed so I could put these two rooms back to some sort of order. Phew!
A decent amount of electrical work had also been completed. The wiring to our old heating system was mostly removed, it was using three circuits for reasons best known to the plumbers 13 years ago. Also, our septic tank is attached to one of them. The wiring to this was tidied up admirably, leaving it neat and tidy and better than before!
A new consumer unit was attached to the wall next to our old one. Little bit of a pain, but I can see the argument for this. If you’re wondering – they could have used our existing consumer unit if it had spare capacity. But also, they will not use it if it’s not a metal consumer unit with surge protection. Now, our main consumer unit is scheduled for replacement in a couple of months by our electrician, by such a unit. I wish we had known this info beforehand as we would have brought that date forward. I think we will consolidate the two when our electrician does this work, just might have to pay him some more!
Bathroom ‘Before’ Radiator
Bathroom ‘After’ Radiator
Day Two
Similar numbers of people appear, they’re all very friendly though and happy to get cracked on doing whatever they’re doing. (You might want to apologise to any nice neighbours you have about all the vans). There’s certainly no slacking going on, just getting on with things. The main large piping run from the heat pump to the cylinder location gets properly underway. This looks like about 60mm once pipe insulation is on. Following pre-agreed routes which I am happy with being able to box in when they’ve finished. I think our house bricks – early 20th century and very hard – put up a challenge, but to be fair, he didn’t grumble about it.
Both day 1 & 2 has some truly awful weather. Storm Debi said hi and can’t have been much fun to work outside in. They did their best to close doors to the lounge/ dining room where we were keeping out the way!
Over the course of the day, I mostly kept out the way and let them get on. I needed to move a chest of drawers on the landing at one point for the new cylinder to get past, but that was about all I needed to do.
End of the Second Day
Daily run down time………all radiators other than the bathroom are now plumbed up. The somewhat awkward loft radiator has been attached. A number of years ago whilst in a crawl space in part of the loft, I dragged through 2 plastic pipes with a plan to have these connected, I never did. These were able to be utilized for the installation. Plastic is certainly not their preference, but there’s no access to the crawl space any more, they are 15mm JG Speedfit, so they used them and just joined copper at each accessible end.
There was a lot of work put in to re-piping for the two kitchen radiators. The pipe run supplying both was replaced with 22mm (from 15mm). Then reduced to 15mm for each individual radiator. This is all about flow rates, bigger pipes, more water flowing at lower temperatures. The geek in me finds this nicely sculpted copper pipework very satisfying. Elegant bends where appropriate, etc. Again, following agreed and discussed route where I can easily box them in afterwards.
The heat pump is now in place. On a base constructed of timber frame and gravel underneath. I had previously just expected it to be sat on the gravel drive, but it looks rather neat how it’s done. It could have gone a little closer to the house wall, but advised that if I am happy, its ideal location is there. They like airflow and space around them for this. It’s perhaps a smidge further out than I would have gone with. But our house has been bloomin’ freezing and expensive to heat for far too long, so we are just embracing it and going with any recommendations. We have put a lot of work into insulating anything we can and replacing single glazed windows, etc. It would seem foolish to do anything which makes it less efficient, even just a little.
The weather was terrible and our poor installers had this mud pit to contend with!
This photo is at the top of the page, but I thought it was worth adding again here to be an ‘after’ in contrast to the muddy ‘before’! (We graveled the drive after the installers had gone and it looks smart!)
That’s my lot I think, there’s a lot of rubbish, but am told the rubbish collection people are scheduled for Friday. Might need some new gravel, the old was rather past its best before, but has elevated itself to mud pit levels now.
Day Three
Everyone is here again. Yes, we apologized to our nice neighbour about the van invasion. Fortunately she is very understanding!
The electricians are back again, they were somewhere else on Tuesday. Doing what electricians do. Getting soaked on the driveway into the bargain. They were doing various wiring inside my shiny new heat pump, between the heat pump and the cylinder and to the cylinder itself. The carpet and floor came up again in a bedroom for this. We also had another discussion about the thermostat and the Daikin Madoka (control panel/posh thermostat) location! We’ve discussed this a few times now, but finally decided on a spot on the landing near the cylinder. In a little row alongside my existing (electric) underfloor heating controller for the bathroom.
We will be getting two control units for the system. One is the Daikin Madoka, which does all sorts of techy stuff with the heat pump, along with more standard room thermostat/schedule control for the heating. The Madoka has an app to control it so I am happy with the location there. Otherwise I would have wanted at least one of them downstairs for easier access. Read more about them later, when I have had chance to play with them and figure them out myself.
Daikin Madoka Control Panel
Daily rundown time, my lead installer advised me that to start the day off, he had redone a chunk of the cylinder plumbing! He had delegated this to one of the newer members of the Octopus installation team, but evidently wasn’t entirely happy. Good to know they keep an eye on this and aren’t afraid to decide it’s not up to their standards. I’m sure the first iteration would have worked, but perhaps not as well as it should. They also hooked up an extension lead to power the immersion heater. So, we now had hot water back! It was setup on a timer with an RCD and we had a cylinder full of lovely hot water. If we were to use up the cylinder before morning, we had instructions on how to reheat, we didn’t need to.
The plan at this point seems to hopefully get finished off with the bulk of the work on Thursday. Hopefully just leaving commissioning and testing on Friday, and hopefully some heat, I am jolly chilly right now……
Day Four
Things seem to be calming down a little today. Everyone is still here doing stuff, but it’s seeming like the bulk of the work around the house is done.
Moving straight to the summary as it was less obvious what was going on until the end. The electricians are doing more wiring under a bedroom floor. The Daikin Madoka is in place, awaiting the thermostat to be delivered, advised Friday for this. Also a small but vital component is coming Friday. I think it perhaps should have been here initially, but the electrician is making sure it is en route! I think they can all sympathise with the lack of heating, did I mention we haven’t had traditional radiators for about 5 years now! Our immersion is however hooked up for the evening.
The system is filled up with water towards the end of the day. A bit of what we’ll call – frantic soldering – ensues. I’ll let them off, there’s been a lot of new pipework gone in this week. And it only leaked above the one piece I (deliberately) haven’t plaster-boarded in the kitchen, below the cylinder. As far as I know, that was the only leaking bit, so far…….
Not much more to report for the day, Friday is hopefully more exciting!
Landing Radiator ‘Before’ Picture
Landing Radiator ‘After’ Picture
Day Five
They’re starting to tidy up and disperse tools and parts back to vans. This must be a positive sign.
The bathroom radiator should be getting connected, not sure why it wasn’t so far, but no matter! Oh, it was just connected and spurted water through the ceiling, oops. This is again my unfinished ceiling so I am quite relaxed about it. One chap did run down and do his best to get mopping.
Also, a Luton van reverses up and the huge pile of scrap and rubbish mysteriously vanishes and our driveway looks instantly better! Very efficient.
What else is left? Lots of pipe insulation, everywhere. More electrics. He had to remove various circuits from our old heating system, but leave one connected to our septic tank, you don’t want to know what happens if he breaks that
